Wellington Amateur Radio Club - ZL2WB

Over the summer we are having informal shed workshops. No set topic, but all are welcome to come along, preferably (but optionally) with your soldering iron and a project to work on. That might be a uBITx transceiver, a magnetic loop antenna, a power supply, an arduino nano keyer project, or whatever takes your fancy. There are eight magnetic loops under construction for a start! #1 in the summer series kicked off at Bernard's QTH, 1 Winsley Terrace, Churton Park, from 1pm - 3pm, on Sunday 7 October 2018. Eight turned up, with George ZL2AG and Don ZL2BD talking about their regenerative and super-regenerative receivers.

Our meeting of 19 September 2018 featured youtube clips on amateur radio topics. We watched the following clips. How to build a dummy load https://www.youtube.com/watch?v=O9FLgWoyfsY The new Yaesu FTDX101D https://www.youtube.com/watch?v=I_iZU4Znl2s https://www.youtube.com/watch?v=A1TDFzfBASE A very simple arduino nano based CW keyer https://www.youtube.com/watch?v=0FU66Joi6_Y A kitset bench power supply 0-30v https://www.youtube.com/watch?v=DLxOwVw1NEE QSX transceiver from QRP-LABs https://www.youtube.com/watch?v=hL6CWaY438Y The µBITx transceiver https://www.youtube.com/watch?v=pFGnssTBdjA https://www.youtube.com/watch?v=l33S1ERz-tg Win4icom Windows Software for the iCOM 7300 https://www.youtube.com/watch?v=mVVm5KambB0 https://www.youtube.com/watch?v=4rB3Rtma0uA Magnetic loops https://www.youtube.com/watch?v=E56wIlpfZgA https://www.youtube.com/watch?v=Al3ZJipFq6k Teddy shoots into space above Auckland https://www.youtube.com/watch?v=2lzCP0CQmYU    

At the last "formal" workshop for the year on 9 September 2018, held at ZL2XJ's QTH, we were given tips on the construction of power supplies by three members (Don ZL2BL, Bernard ZL2BD, and George ZL2AG). This included: a foolproof (but weighty) bench power supply for valve circuits (short circuits no problem) using readily available transformers and valves (Don ZL2BL) two different kits for variable voltage bench power supplies, acquisition of low cost 13.8v switched mode power supplies, and tips on how to quieten down RF noise from these power supplies (Bernard ZL2BD) low cost 13.8v transformer-based power supplies built into older desktop computer cases (George ZL2AG). Over the summer we will have informal workshops, where you are welcome to "bring along the soldering iron" to work on projects, whether that be a uBITx transceiver, a magnetic loop antenna, or a power supply or whathaveyou. Relevant documents [wpdm_package id='3540'] [wpdm_package id='3549'] [wpdm_package id='3544'] [wpdm_package id='3546']

At the August 2019 meeting we set out to find out which team had the competitive edge in finding a set of crystals that would be useful in a 12 MHz crystal filter? Bernard and Frank found 3 crystals within 30Hz of each other. They were part way to getting a set of eight. A bit harder than everybody thought, but many learnt some techniques in sorting out crystal suitability. The other two teams each found 2 pairs of crystals that would meet the required specifications.

Bernard ZL2BD hosted another shed workshop on Sunday 5 August 2018 from 1pm -3pm at his QTH. Due to interest in Small Magnetic Loop antennas, this month's workshop was a follow on session to assist those committed to construct a loop antenna. Several people purchased Capacitor Kits to make an air spaced butterfly capacitor. Progress is being made on sourcing LDF4-50 1/2” coax and possibly LDF 5-50 1” coax for the loop material to be made available to those who want this material. It's not too late to order a kit if you haven't done so. Bernard talked about practical matters, such as how to construct the capacitor enclosure and plastic waterpipe housing for the antenna, as well as practical details on putting together the capacitor kit, and selection of motor drivers and gearbox, etc. Mike ZL1AXG talked to a design that provides for real-time tracking and tuning of a magnetic loop. A circuit board is available to purchase from North America. He talked about where to source components including the processor (Teensy 3.2), a 100 step rotation encoder, 51uH twin coil chokes, the stepper motor driver chips, and the stepper motor and gearbox. Bernard provided pre-calculated details for a 2m…